50Cr5MoV支承辊用钢氧和夹杂物控制实践

炼钢

50Cr5MoV支承辊用钢氧和夹杂物控制实践

薛永栋1,2，张威风2，辛雪倩2，李春辉2，杨金安2

（1.洛阳理工学院机械工程学院，河南洛阳 471003； 2.洛阳中重铸锻有限责任公司铸锻工程技术与材料研究院，河南洛阳 471003）

接受日期:1900-01-01 出版日期:2020-02-05

Practice on control of oxygen and inclusions for 50Cr5MoV backup rolls

Accepted:1900-01-01 Online:2020-02-05

摘要/Abstract

摘要： 结合生产实践，采用“EAF（电炉初炼）→LF（炉外精炼）→VD（真空脱气）→LF返加热→VC（真空浇铸）”工艺，通过配料配碳，EAF初炼炉控碳减少钢水过氧化，LF精炼过程准确控制精炼渣成分深度脱氧和脱硫，VD过程有效控制真空脱气处理时间和真空度，LF返加热控制软吹气量来避免卷渣，浇铸过程采用精炼中间包、真空浇铸和水口吹氩等手段，50Cr5MoV材质支承辊钢锭氧质量分数控制在20×10-6以下，锻件高倍分析下夹杂物含量合格，该类支承辊锻件超声波探伤合格，加工过程夹杂物外露现象明显减少。

关键词: 支承辊, 精炼渣, 氧含量, 夹杂物

Abstract: Combined with production practice, the carbon content reasonably was controlled in scrapped charge process and during arc furnace to decrease peroxidation of molten steel, final slag composition was aimed during LF process to remove oxygen and sulphur deeply, vacuum degassing time and efficient vacuum degree was carried out during VD process, gas flow was controlled during back to LF process to reduce slag entrapment, the refining ladle was adopted during the whole steelmaking process and blowing argon around the ladle nozzle was carried out during VC process. Results shows final oxygen mass fraction of backup roll were all below 20×10-6 and forging inclusions in microscope was qualified, ultrasonic examination was qualified and inclusions exposure were effectively reduced during subsequent machining process.

Key words: backup rolls, refining slag, oxygen content, inclusion

薛永栋1,2，张威风2，辛雪倩2，李春辉2，杨金安2. 50Cr5MoV支承辊用钢氧和夹杂物控制实践[J]. 炼钢.

[1]	王举金1，孔祥玉2，孟润泽2，张旭辉2，任英1. Q195热轧带钢脱氧过程非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 13-20.
[2]	张建元1，季莎2，张立峰3，陆晓雷1，陈威2，张海礼1. 20CrMnTiH齿轮钢脱氧过程中非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 21-26.
[3]	万文1，马德刚2，李经哲2，马旭朝3. 冷轧薄板超低碳钢精炼双联工艺研究及应用[J]. 炼钢, 2020, 36(3): 27-31.
[4]	张国锋1，季莎2，张立峰3，王亚栋2，李彩云1，张威1，罗艳2. 20CrMnTiH齿轮钢凝固和冷却过程中非金属夹杂物的转变研究[J]. 炼钢, 2020, 36(3): 32-38.
[5]	夏兆东1，邓丽琴1，王德永2. 梅钢250t钢包浇铸过程旋涡卷渣行为研究[J]. 炼钢, 2020, 36(3): 44-50.
[6]	安会龙1，任英2*，刘洋2，储焰平2，张彦辉2. 弹簧钢中夹杂物生成热力学[J]. 炼钢, 2020, 36(3): 55-61.
[7]	齐广，王福明，沈伟. 低飞溅气保焊丝钢ER70S-6夹杂物的塑性化控制[J]. 炼钢, 2020, 36(3): 62-67.
[8]	赵晓磊1，成功2，杨华峰1，刘丽娟1，任英2. GCr15轴承钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(2): 22-28.
[9]	王祎,张立峰2，杨文1，雷勋惠1，张继1，赵根安1. Q345钢液凝固及铸坯冷却过程中非金属夹杂物的组成演变[J]. 炼钢, 2020, 36(2): 29-33.
[10]	徐佳林1,2,3，陆海飞1,2,3，田伟光1,2,3，蒋发立2,3. 304不锈钢冷轧板线鳞缺陷改进实践[J]. 炼钢, 2020, 36(2): 70-75.
[11]	屈志东，谢有，孟晓玲，徐建飞，王昆鹏. 高品质轴承钢BOF-LF-RH-CC和EAF-LF-VD-CC工艺夹杂物演变规律[J]. 炼钢, 2020, 36(2): 76-80.
[12]	王建忠1,程礼梅2,任英2,赵晓锋1,李慧峰1,王举金2. 含硫齿轮钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(1): 8-14.
[13]	张明海1，程礼梅2，杨文2，李学科1，于春强1，牛凯军2. 含硫齿轮钢凝固冷却过程中非金属夹杂物的转变研究 [J]. 炼钢, 2020, 36(1): 21-26.
[14]	刘风刚1,2，任英1，段豪剑1，张立峰1. 钢包软吹过程优化数学模拟和工业试验研究[J]. 炼钢, 2019, 35(6): 24-30.
[15]	杨光维1，陈兆平1，柳向椿2，徐超2. VD镇静时间对齿轮钢大颗粒夹杂物的影响[J]. 炼钢, 2019, 35(6): 31-34.