RH脱硫对无取向电工钢中夹杂物的影响

摘要/Abstract

摘要： 研究了RH脱硫对常规工艺（连铸+热轧）和CSP工艺下的无取向电工钢材样中夹杂物的影响。两种工艺下，当CaO-CaF2脱硫剂加入量为1～4 kg/t时，RH脱硫率约为25 %。终渣氧化性高、曼内斯曼指数（MI）低是影响脱硫效果的原因之一。CSP产线RH采用“先铝后硅”的脱氧方式，材样中夹杂物主要是AlN、MnS、CaS和少量铝酸钙。此时，夹杂物总量主要受氮含量影响，硫含量只与硫化物夹杂密度呈正比关系。常规产线RH采用“先硅后铝”脱氧方式，材样中氧化物夹杂和AlN夹杂含量相当，含钙夹杂物数量只占夹杂物总量的12%左右。脱硫剂中CaF2对耐材的侵蚀导致RH脱硫时材样中含Mg夹杂数量是不脱硫时的2倍。

关键词: RH脱硫, 夹杂物, 无取向电工钢

Abstract: The effect of RH desulphurization on inclusions in non oriented electrical steel through conventional process (continuous casting + hot rolling) and CSP process has been studied in this paper. When the amount of CaO-CaF2 desulfurizer is 1～4 kg/t， the RH desulfurization rate is about 25 %. The high oxidation of final slag and low MI value are one of the reasons for the desulfurization effect. The RH of CSP process is deoxidized by “aluminium followed by silicon”. The inclusions are mainly AlN, MnS, CaS and a small amount of calcium aluminate. At this time, the total amount of inclusions is mainly affected by nitrogen content, and the sulfur content is proportional to the density of sulfide inclusions. The RH of conventional process is deoxidized by “silicon followed by aluminium”. The content of oxide inclusions and AlN inclusions in the sample is equal, and the amount of Ca inclusions only accounts for about 12 % of the total inclusions. The corrosion of CaF2 from desulfurizer to refractories results in the amount of Mg inclusions in RH desulfurization sample twice as much as that in non-desulfurization.

Key words: RH desulphurization, inclusion, Non oriented electrical steel

隋亚飞，李慈颖，刘彭，徐刚军. RH脱硫对无取向电工钢中夹杂物的影响[J]. 炼钢, 2019, 35(2): 34-38.

[1]	王举金1，孔祥玉2，孟润泽2，张旭辉2，任英1. Q195热轧带钢脱氧过程非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 13-20.
[2]	张建元1，季莎2，张立峰3，陆晓雷1，陈威2，张海礼1. 20CrMnTiH齿轮钢脱氧过程中非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 21-26.
[3]	万文1，马德刚2，李经哲2，马旭朝3. 冷轧薄板超低碳钢精炼双联工艺研究及应用[J]. 炼钢, 2020, 36(3): 27-31.
[4]	张国锋1，季莎2，张立峰3，王亚栋2，李彩云1，张威1，罗艳2. 20CrMnTiH齿轮钢凝固和冷却过程中非金属夹杂物的转变研究[J]. 炼钢, 2020, 36(3): 32-38.
[5]	夏兆东1，邓丽琴1，王德永2. 梅钢250t钢包浇铸过程旋涡卷渣行为研究[J]. 炼钢, 2020, 36(3): 44-50.
[6]	安会龙1，任英2*，刘洋2，储焰平2，张彦辉2. 弹簧钢中夹杂物生成热力学[J]. 炼钢, 2020, 36(3): 55-61.
[7]	齐广，王福明，沈伟. 低飞溅气保焊丝钢ER70S-6夹杂物的塑性化控制[J]. 炼钢, 2020, 36(3): 62-67.
[8]	赵晓磊1，成功2，杨华峰1，刘丽娟1，任英2. GCr15轴承钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(2): 22-28.
[9]	王祎,张立峰2，杨文1，雷勋惠1，张继1，赵根安1. Q345钢液凝固及铸坯冷却过程中非金属夹杂物的组成演变[J]. 炼钢, 2020, 36(2): 29-33.
[10]	徐佳林1,2,3，陆海飞1,2,3，田伟光1,2,3，蒋发立2,3. 304不锈钢冷轧板线鳞缺陷改进实践[J]. 炼钢, 2020, 36(2): 70-75.
[11]	屈志东，谢有，孟晓玲，徐建飞，王昆鹏. 高品质轴承钢BOF-LF-RH-CC和EAF-LF-VD-CC工艺夹杂物演变规律[J]. 炼钢, 2020, 36(2): 76-80.
[12]	王建忠1,程礼梅2,任英2,赵晓锋1,李慧峰1,王举金2. 含硫齿轮钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(1): 8-14.
[13]	张明海1，程礼梅2，杨文2，李学科1，于春强1，牛凯军2. 含硫齿轮钢凝固冷却过程中非金属夹杂物的转变研究 [J]. 炼钢, 2020, 36(1): 21-26.
[14]	薛永栋1,2，张威风2，辛雪倩2，李春辉2，杨金安2. 50Cr5MoV支承辊用钢氧和夹杂物控制实践[J]. 炼钢, 2020, 36(1): 67-72.
[15]	刘风刚1,2，任英1，段豪剑1，张立峰1. 钢包软吹过程优化数学模拟和工业试验研究[J]. 炼钢, 2019, 35(6): 24-30.

RH脱硫对无取向电工钢中夹杂物的影响

Effect of RH desulphurization on inclusions in non oriented electrical steel

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价