无取向硅钢薄板坯连铸液面波动和水口结瘤控制

炼钢 ›› 2017, Vol. 33 ›› Issue (6): 37-41.

无取向硅钢薄板坯连铸液面波动和水口结瘤控制

李大鹏1, 2，薛文辉1，吴华章1，王海风2

1. 本溪钢铁（集团）有限责任公司，辽宁本溪 117021； 2. 钢铁研究总院先进钢铁流程及材料国家重点实验室，北京 100081

接受日期:1900-01-01 出版日期:2017-12-05

Mold level fluctuation and submerged entry nozzle clogging control of thin slab continuous casting for nonoriented silicon steel

Accepted:1900-01-01 Online:2017-12-05

摘要/Abstract

摘要： 不同于鼓肚导致的亚包晶钢液面波动，针对无取向硅钢薄板坯连铸结晶器液面严重波动的问题，通过研究浸入式水口结瘤对结晶器流场的影响、分析事故时操作与液位曲线的现场数据，可推断出结晶器液面波动的主要原因是大量未去除的脱氧产物所造成的浸入式水口结瘤。本溪钢铁（集团）有限责任公司炼钢厂的生产实践表明：通过采取精准控制转炉终点钢水w(O)至800×10-6以下、RH后期软吹氩流量从150～200 L/min减小到40～50 L/min、适当提高中间包钢水过热度在25～45 ℃等技术措施，无取向硅钢结晶器液面的波动幅度从±15 mm以上降低至±3 mm以内。

关键词: 无取向硅钢, 液面波动, 浸入式水口, 结瘤

Abstract: As distinguished from the level fluctuation caused by bulging for hypo-peritectic steel，aiming at serious mold level fluctuation of thin slab continuous casting for non-oriented silicon steel，by means of researching the effect of the submerged entry nozzle clogging on mold flow field and analyzing the workshop data of accident operation and level curve，it was inferred that the main cause for level fluctuation was the submerged entry nozzle clogging resulted from a great deal of deoxidation products which had not been efficiently removed. The production practice at steelmaking plant of Bensteel indicated that mold level fluctuation range during non-oriented silicon steel casting had been dropped from more than±15 mm to less than±3 mm through some technical measures as controlling accurately blowing end-point oxygen mass fraction of molten steel below 800×10-6，reducing argon flow rate from 150-200 L/min to 40-50 L/min at the later stage of RH，and raising properly superheat to 25-45 ℃ of liquid steel in tundish.

Key words: non-oriented silicon steel, mold level fluctuation, submerged entry nozzle, clogging

李大鹏1, 2，薛文辉1，吴华章1，王海风2. 无取向硅钢薄板坯连铸液面波动和水口结瘤控制[J]. 炼钢, 2017, 33(6): 37-41.

[1]	汪国才，李浩，陶承岗，张诚. 连铸圆坯表面纵裂原因及控制措施[J]. 炼钢, 2020, 36(2): 53-59.
[2]	伍旋1,2，王明林2，张延玲1，张慧2，张开发2. 高拉速板坯结晶器流场影响因素的模拟研究[J]. 炼钢, 2020, 36(1): 27-33.
[3]	李萍，李四军，彭永香，付常伟，卢波 . 非平衡布流异型坯结晶器水口结构优化的物理模拟 [J]. 炼钢, 2020, 36(1): 43-49.
[4]	田立，田运辉，谢卫东，李英姿，肖小文. 基于前馈补偿方式的板坯结晶器液面周期性波动研究[J]. 炼钢, 2019, 35(4): 38-42.
[5]	陈刚1，周海龙1，喻林1，钟良才2，张开坚1. 浸入式水口结构对板坯结晶器液面波动的影响[J]. 炼钢, 2018, 34(5): 50-56.
[6]	翟万里，左辉，马建超，印传磊. 含硫含铝钢浇铸结瘤原因分析及改进[J]. 炼钢, 2018, 34(2): 19-24.
[7]	吴光辉1，唐海燕1，程鹏飞1，郭晓晨1，张家泉1，甄先锋2，张海涛2，王时松2. 浸入式水口结构对180 mm×240 mm断面连铸结晶器内钢液流动行为的影响[J]. 炼钢, 2017, 33(4): 31-38.
[8]	李积鹏1,2，程树森1，程子建2，冯永平2，邹明2，郭靖1. BOF→RH→CSP工艺生产含钛IF钢[J]. 炼钢, 2017, 33(4): 46-51.
[9]	朱守欣1，于湛1，殷皓1，唐萍2，李敬想2，李玉林2. 轴承钢水口结瘤与棒材中大型夹杂物关系研究[J]. 炼钢, 2017, 33(1): 73-78.
[10]	赵定国，高茗，李新，王书桓. 带吸附杆水口内钢液及夹杂物运动物理模拟[J]. 炼钢, 2016, 32(6): 51-56.
[11]	张立峰. 钢中非金属夹杂物几个需要深入研究的课题[J]. 炼钢, 2016, 32(4): 1-16.
[12]	赵家七，邹长东，马建超，耿涛. RH脱氧工艺优化对W470无取向硅钢洁净度的影响[J]. 炼钢, 2015, 31(4): 21-25.
[13]	乔焕山，王保生，王莉，陈玉鑫. 铝镇静钢水口结瘤问题的实践研究[J]. 炼钢, 2015, 31(1): 56-60.
[14]	李梦英，张洪波，杨杰，王占国，佟志新，冯慧霄. 低碳铝镇静钢热轧板表面夹渣的原因分析与控制[J]. 炼钢, 2014, 30(6): 28-31.
[15]	邓叙燕1，2，马建超1，赵伟杰1. 脱氧制度对H08C焊丝钢连铸水口结瘤的影响[J]. 炼钢, 2014, 30(6): 42-45.