BOF→RH→CSP工艺生产含钛IF钢

炼钢 ›› 2017, Vol. 33 ›› Issue (4): 46-51.

BOF→RH→CSP工艺生产含钛IF钢

（1.北京科技大学冶金与生态工程学院，北京 100083； 2.酒泉钢铁（集团）有限责任公司，甘肃嘉峪关 735100）

接受日期:1900-01-01 出版日期:2017-08-05

Investigation on clogging mechanism of submerged entry nozzle for Ti-bearing IF steel during BOF→RH→CSP process

Accepted:1900-01-01 Online:2017-08-05

摘要/Abstract

摘要： 针对BOF→RH→CSP工艺生产含钛IF钢浸入式水口结瘤问题，采用扫描电镜、能谱分析等方法，分析了IF钢浇铸过程水口结瘤物的组成，结合中间包夹杂物的特性，阐明了水口结瘤的机理。结果表明：钛元素的存在一方面使钢水中Al2O3夹杂物不易碰撞长大，另一方面减小了钢液、耐材和夹杂物之间的润湿角，容易造成水口结瘤；结瘤物初始沉积层主要为钢水与水口耐材反应生成的以Al2O3为主的复合氧化物；而结瘤物主体层主要来源于钢水中的夹杂物，为低变性的MgO·Al2O3尖晶石或Al2O3，且含有钢滴；夹杂物沉积进而烧结成疏松的网状层，使钢水更易粘附从而加剧了水口结瘤速度。研究结果可为优化工艺参数、提高BOF→RH→CSP工艺连浇炉数和产品质量提供可靠的理论指导。

关键词: 含钛IF钢, 水口结瘤, 夹杂物沉积

Abstract: In order to investigate the clogging mechanism of submerged entry nozzle during casting Tibearing IF steel by BOF→RH→CSP process.The composition of clogs on submerged entry nozzle was studied by scanning election microscopy (SEM), energy dispersive spectroscopy (EDS).Finally, the clogging mechanisms of submerged entry nozzle were elucidated by combining with the characteristics of inclusion in tundish.The investigated results indicated that the clogging easily occurs because that wetting angle was decreased due to containing titanium in molten steel.The clogs close to the inner surface of submerged entry nozzle, which was composite oxide of Al2O3-CaO-SiO2-MgO but mainly consists of Al2O3, was resulted from reaction between refractory material of SEN and acidsoluble aluminum in molten steel.However, the clogs close to molten steel comes from the deposition of inclusions containing Al2O3 or spinel of MgO·Al2O3 and iron particles.The rate of clogging was increased because that the molten steel easily adhered to net sintered inclusions.The studied results will provide theoretical guidance for rising the continuous casting heats of tundish and improving the quality of products by means of optimizing the process parameters.

Key words: Ti-bearing IF steel, clogging of SEN, deposition of inclusion

李积鹏1,2，程树森1，程子建2，冯永平2，邹明2，郭靖1. BOF→RH→CSP工艺生产含钛IF钢[J]. 炼钢, 2017, 33(4): 46-51.

[1]	翟万里，左辉，马建超，印传磊. 含硫含铝钢浇铸结瘤原因分析及改进[J]. 炼钢, 2018, 34(2): 19-24.
[2]	朱守欣1，于湛1，殷皓1，唐萍2，李敬想2，李玉林2. 轴承钢水口结瘤与棒材中大型夹杂物关系研究[J]. 炼钢, 2017, 33(1): 73-78.
[3]	张立峰. 钢中非金属夹杂物几个需要深入研究的课题[J]. 炼钢, 2016, 32(4): 1-16.
[4]	乔焕山，王保生，王莉，陈玉鑫. 铝镇静钢水口结瘤问题的实践研究[J]. 炼钢, 2015, 31(1): 56-60.
[5]	邓叙燕1，2，马建超1，赵伟杰1. 脱氧制度对H08C焊丝钢连铸水口结瘤的影响[J]. 炼钢, 2014, 30(6): 42-45.
[6]	张祥艳;陈兴伟;张春燕;陈春生;张晓香;李毅平. 硬线钢LF增铝理论计算及水口结瘤分析[J]. , 2012, 28(5): 56-60.
[7]	王春锋;吴健鹏;夏春祥;赵继宇;何金平. 武钢CSP高铝钢浇铸过程水口结瘤问题研究[J]. , 2012, 28(5): 65-68.
[8]	冯远超;曾建华. 改善低合金钢浇铸性能的研究[J]. , 2010, 26(4): 46-49.
[9]	陈伟;苏鹤洲;张卫强. ML35钢浇铸过程水口结瘤原因分析及控制[J]. , 2009, 25(02): 19-21,3.
[10]	吴健鹏;王金平;于学斌. 冷墩钢钙处理工艺研究与应用[J]. , 2009, 25(01): 4-7,46.
[11]	佐祥均;张立峰;刘石虹;梁玫;牛士珍;李春增;王新华. 中碳钢连铸中碳质水口结瘤现象的研究[J]. , 2008, 24(06): 27-32.
[12]	王晓峰;陈伟庆;裴凤娟;候成. 板坯连铸水口结瘤机理研究[J]. , 2007, 23(06): 20-22,2.