不同脱氧工艺对SG45VCM钢中夹杂物的影响

摘要/Abstract

摘要： 为解决钢厂生产SG45VCM钢时常出现的因脱氧工艺不合理造成的Al2O3夹杂物聚集堵塞水口问题，通过热力学计算及试验，研究不同脱氧工艺对钢中非金属夹杂物的影响。热力学计算表明：铝和钛脱氧均可使钢中溶解氧降至较低的水平，铝和钛的脱氧能力远大于硅和锰。2种脱氧工艺终点钢中全氧质量分数相差不大，最低降至7×10-6。新脱氧工艺所形成的夹杂物尺寸较小，各种类夹杂物数量相当，且在钢中分布均匀，可避免原脱氧工艺所形成的纯Al2O3夹杂造成的水口结瘤现象，同时结果表明，钢中铝的存在不利于钛氧化物的形成，钢中钛的存在可以使夹杂物呈均匀弥散分布。

关键词: 炼钢, 脱氧合金化, 氧质量分数, 夹杂物, 优化

Abstract: In order to eliminate clogging of nozzle that caused by the the accumulation of Al2O3 which was generated in the irrational process of deoxygenation during concasting SG45VCM steel, research on the influence of different deoxidization processes on nonmetallic inclusions in steel was studied, through thermodynamic calculation and experiments. Thermodynamic calculation shows that deoxidization by using aluminum and titanium can get low dissolved oxygen level, deoxidization ability of aluminum and titanium is better than that of silicon and manganese. At the end of two kinds of deoxidization process the oxygen mass fraction in steel were similar, the lowest was 7×10-6. Size of inclusions in the new deoxidization process was small. There were various types of inclusions, and they were distributed evenly in the steel. Phenomenon of clogging of nozzle caused by the pure Al2O3 which was generated in the original process of deoxygenation could be avoided. The experiment results show that the presence of aluminum in steel can against the formation of titanium oxide, and the inclusion distribution is uniform dispersion.

Key words: steelmaking, deoxidation alloying, oxygen mass fraction, inclusions, optimize

战东平，邱国兴1，张炎杰1，牛奔1，姜周华1，张慧书2. 不同脱氧工艺对SG45VCM钢中夹杂物的影响[J]. 炼钢.

[1]	李琳1，2，周立磊1，2，李明明1，2，李强1，2，邹宗树1，2. 漩流氧枪应用于转炉炼钢的水模试验研究[J]. 炼钢, 2020, 36(3): 1-6.
[2]	王举金1，孔祥玉2，孟润泽2，张旭辉2，任英1. Q195热轧带钢脱氧过程非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 13-20.
[3]	张建元1，季莎2，张立峰3，陆晓雷1，陈威2，张海礼1. 20CrMnTiH齿轮钢脱氧过程中非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 21-26.
[4]	万文1，马德刚2，李经哲2，马旭朝3. 冷轧薄板超低碳钢精炼双联工艺研究及应用[J]. 炼钢, 2020, 36(3): 27-31.
[5]	张国锋1，季莎2，张立峰3，王亚栋2，李彩云1，张威1，罗艳2. 20CrMnTiH齿轮钢凝固和冷却过程中非金属夹杂物的转变研究[J]. 炼钢, 2020, 36(3): 32-38.
[6]	夏兆东1，邓丽琴1，王德永2. 梅钢250t钢包浇铸过程旋涡卷渣行为研究[J]. 炼钢, 2020, 36(3): 44-50.
[7]	安会龙1，任英2*，刘洋2，储焰平2，张彦辉2. 弹簧钢中夹杂物生成热力学[J]. 炼钢, 2020, 36(3): 55-61.
[8]	齐广，王福明，沈伟. 低飞溅气保焊丝钢ER70S-6夹杂物的塑性化控制[J]. 炼钢, 2020, 36(3): 62-67.
[9]	刘显杰1, 窦群康2，闵文博2，陈天耀3，薛正良4. 变压吸附制氧及其在电弧炉炼钢中的应用[J]. 炼钢, 2020, 36(2): 6-9.
[10]	赵晓磊1，成功2，杨华峰1，刘丽娟1，任英2. GCr15轴承钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(2): 22-28.
[11]	王祎,张立峰2，杨文1，雷勋惠1，张继1，赵根安1. Q345钢液凝固及铸坯冷却过程中非金属夹杂物的组成演变[J]. 炼钢, 2020, 36(2): 29-33.
[12]	蔡亦凡1，孙彦辉1，杨文中2，黎建全2，陈天明3，李志强3. 变径通道在八字型感应加热中间包中的应用[J]. 炼钢, 2020, 36(2): 42-47.
[13]	徐旺1,2，刘增勋1,2，肖鹏程1,2,朱立光2,3. 方坯表面纵裂的数值模拟研究[J]. 炼钢, 2020, 36(2): 48-52.
[14]	徐佳林1,2,3，陆海飞1,2,3，田伟光1,2,3，蒋发立2,3. 304不锈钢冷轧板线鳞缺陷改进实践[J]. 炼钢, 2020, 36(2): 70-75.
[15]	屈志东，谢有，孟晓玲，徐建飞，王昆鹏. 高品质轴承钢BOF-LF-RH-CC和EAF-LF-VD-CC工艺夹杂物演变规律[J]. 炼钢, 2020, 36(2): 76-80.

不同脱氧工艺对SG45VCM钢中夹杂物的影响

The influence of different deoxidization process on the inclusions in SG45VCM steel

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价