8620RH非调质钢全流程洁净度研究

摘要/Abstract

摘要： 通过Aspex全自动扫描电镜观察“电炉→LF→VD→连铸”工艺生产8620RH非调质钢的全流程夹杂物变化情况，结合钢水中T.O、氮含量的检测结果，分析了冶炼过程中钢液洁净度的变化趋势。研究表明：8620RH非调质钢样品中氧化物夹杂的主要成分是Al2O3-MgO-CaO，以Al2O3为主。增硫操作之后，夹杂物中CaO含量降低，硫化物和氧硫化物含量明显升高。冶炼过程夹杂物中MgO含量逐渐升高，每个工序冶炼后期的样品中含MgO夹杂物数量均明显高于该工序初期，未检测到大尺寸的镁铝尖晶石类夹杂物。采用铝脱氧方式生产的8620RH非调质钢铸坯中平均w(T.O)=10.1×10-6，达到了很高的洁净度，氧化物夹杂数量较少，尺寸较小。铸坯和轧材中氧化物类夹杂物数量均在10个/mm2以下。轧材中硫化物多以包裹在氧化物外部的形式存在，有利于提高产品的综合性能，但轧材中存在较大尺寸的硫化物，可以适当提高钢中的氧含量，形成更多细小弥散的氧化物核心，利于硫化物的析出，改善硫化物的形态，使产品具备更好的切削性能。

关键词: 夹杂物, 8620RH非调质钢, 全流程洁净度

Abstract: In the current study, evolution characteristics of inclusions were evaluated using SEM with automatic scanning feature in 8620RH nonquenched and tempered steel samples during the “EAF→LF→VD→CC”production process. Cleanliness of the steel in producion process were evaluated, combined with the detection of total oxygen and nitrogen of the steel. The results show that type of oxide was Al2O3-CaO-MgO, mainly consisted of Al2O3. After adding sulfur operation, content of CaO in inclusions decreased, and the amount of sulfides and oxysulfides increased obviously. Content of MgO increased gradually during the production process, and number density of inclusions with high MgO content in the end of each production steps was all higher than that in the beginning. Few large spinel inclusions were tested in steel samples. High cleanliness was achieved in 8620RH microalloyed forging steel dioxidized by aluminium，and w(T.O)was 10×10-6 in slab. Number densities of oxides in billets and rolled products are lower than 10 per mm2. Most sulfides adhere to small oxides and grow around them. Most sulfides were adhered to oxides so that it contributed to improvement of machinability, but there are still some largesize sulfides in rolling samples. Proper increase on T.O content could be adopted so that sulfides could percipitate on the tiny oxides and improvement on machinability can be achieved.

Key words: inclusions, 8620RH microalloyed forging steel, cleanliness in production process

阿不力克木·亚森1，刘洋1，单以刚2，于湛2，朱守欣2. 8620RH非调质钢全流程洁净度研究[J]. 炼钢, 2015, 31(6): 40-.

[1]	王举金1，孔祥玉2，孟润泽2，张旭辉2，任英1. Q195热轧带钢脱氧过程非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 13-20.
[2]	张建元1，季莎2，张立峰3，陆晓雷1，陈威2，张海礼1. 20CrMnTiH齿轮钢脱氧过程中非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(3): 21-26.
[3]	万文1，马德刚2，李经哲2，马旭朝3. 冷轧薄板超低碳钢精炼双联工艺研究及应用[J]. 炼钢, 2020, 36(3): 27-31.
[4]	张国锋1，季莎2，张立峰3，王亚栋2，李彩云1，张威1，罗艳2. 20CrMnTiH齿轮钢凝固和冷却过程中非金属夹杂物的转变研究[J]. 炼钢, 2020, 36(3): 32-38.
[5]	夏兆东1，邓丽琴1，王德永2. 梅钢250t钢包浇铸过程旋涡卷渣行为研究[J]. 炼钢, 2020, 36(3): 44-50.
[6]	安会龙1，任英2*，刘洋2，储焰平2，张彦辉2. 弹簧钢中夹杂物生成热力学[J]. 炼钢, 2020, 36(3): 55-61.
[7]	齐广，王福明，沈伟. 低飞溅气保焊丝钢ER70S-6夹杂物的塑性化控制[J]. 炼钢, 2020, 36(3): 62-67.
[8]	赵晓磊1，成功2，杨华峰1，刘丽娟1，任英2. GCr15轴承钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(2): 22-28.
[9]	王祎,张立峰2，杨文1，雷勋惠1，张继1，赵根安1. Q345钢液凝固及铸坯冷却过程中非金属夹杂物的组成演变[J]. 炼钢, 2020, 36(2): 29-33.
[10]	徐佳林1,2,3，陆海飞1,2,3，田伟光1,2,3，蒋发立2,3. 304不锈钢冷轧板线鳞缺陷改进实践[J]. 炼钢, 2020, 36(2): 70-75.
[11]	屈志东，谢有，孟晓玲，徐建飞，王昆鹏. 高品质轴承钢BOF-LF-RH-CC和EAF-LF-VD-CC工艺夹杂物演变规律[J]. 炼钢, 2020, 36(2): 76-80.
[12]	王建忠1,程礼梅2,任英2,赵晓锋1,李慧峰1,王举金2. 含硫齿轮钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(1): 8-14.
[13]	张明海1，程礼梅2，杨文2，李学科1，于春强1，牛凯军2. 含硫齿轮钢凝固冷却过程中非金属夹杂物的转变研究 [J]. 炼钢, 2020, 36(1): 21-26.
[14]	薛永栋1,2，张威风2，辛雪倩2，李春辉2，杨金安2. 50Cr5MoV支承辊用钢氧和夹杂物控制实践[J]. 炼钢, 2020, 36(1): 67-72.
[15]	刘风刚1,2，任英1，段豪剑1，张立峰1. 钢包软吹过程优化数学模拟和工业试验研究[J]. 炼钢, 2019, 35(6): 24-30.

8620RH非调质钢全流程洁净度研究

Study on cleanliness of 8620RH microalloyed forging steel in production process

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价