GCr15轴承钢精炼渣结晶矿相研究

›› 2015, Vol. 31 ›› Issue (5): 27-31.

GCr15轴承钢精炼渣结晶矿相研究

刘志宏¹,张兴中²,李国光³,仇圣桃¹

1. 钢铁研究总院连铸技术国家工程研究中心
2. 中国钢研科技集团有限公司
3. 承德建龙特殊钢有限公司炼钢厂

收稿日期:2014-12-17 修回日期:2015-03-13 接受日期:1900-01-01 出版日期:2015-10-05 发布日期:2015-10-05
通讯作者: 刘志宏 E-mail:l_honly@163.com

Study on crystal morphology of refining slag for GCr15 bearing steel

1. National Engineering Research Center of Continuous Casting Technology, Central Iron and Steel Research Institute
2. China Iron&Steel Research Insititute Group
3.

Received:2014-12-17 Revised:2015-03-13 Accepted:1900-01-01 Online:2015-10-05 Published:2015-10-05

摘要/Abstract

摘要： 针对某钢厂GCr15轴承钢生产过程中精炼渣大量结块，导致钢液吸气，钢中夹杂物增多的问题，采用SEM和XRD分析方法，对不同渣系精炼渣的显微组织和结晶矿相进行分析，研究了不同组分对精炼渣结晶性能的影响。结果表明：GCr15轴承钢精炼渣为多矿相混合体，温降过程中大量析出的高熔点矿相包裹在钙铝酸盐或非晶相外，或分布于钙铝酸盐中，增大钙铝酸盐的结合强度，造成精炼渣结块。优化精炼渣组成处于相图中低熔点物相区，有效解决了精炼渣结块问题，使轧材中w（N）和w（O）合格率分别提高了7.07%，6.26%，非金属夹杂物合格率提高了14.70%，改善了GCr15钢洁净度。

关键词: 轴承钢, 精炼渣, 显微组织, 结晶矿相

Abstract: In order to solve the problem that lots of solidified crust of the refining slag during the production process of the GCr15 bearing steel，which resulted the sharply increase of gas and inclusion content in steel，the microstructure and crystal morphology of the refining slag was investigated by SEM and XRD, and the effect of the different composition on crystal morphology was studied. The results showed that the refining slag contained several crystalline phases，and numerous high-melting phases separated out with the decrease of temperature and wrapped up calcium aluminates or strengthened calcium aluminates，which made the refining slag crusted. The composition was optimized in low-melting phase zone，which prevented the solidified crusts effectively. And the qualified rate of w（N）and w（O） were increased by 7.07% and 6.26% in rolled bar，the qualified rate of non-metallic inclusions was increased by 14.70%，the cleanliness of GCr15 steel was improved.

Key words: bearing steel, refining slag, microstructure, crystal morphology

刘志宏张兴中李国光仇圣桃. GCr15轴承钢精炼渣结晶矿相研究[J]. , 2015, 31(5): 27-31.

[1]	赵晓磊1，成功2，杨华峰1，刘丽娟1，任英2. GCr15轴承钢脱氧过程中非金属夹杂物生成热力学及工业实践 [J]. 炼钢, 2020, 36(2): 22-28.
[2]	屈志东，谢有，孟晓玲，徐建飞，王昆鹏. 高品质轴承钢BOF-LF-RH-CC和EAF-LF-VD-CC工艺夹杂物演变规律[J]. 炼钢, 2020, 36(2): 76-80.
[3]	薛永栋1,2，张威风2，辛雪倩2，李春辉2，杨金安2. 50Cr5MoV支承辊用钢氧和夹杂物控制实践[J]. 炼钢, 2020, 36(1): 67-72.
[4]	陈林权1，孙建新2，张思维3，陈然2. 转炉炼钢厂钢包包衬耐材的改进[J]. 炼钢, 2019, 35(5): 5-9.
[5]	王向红，张建斌，屠兴圹，张正林. 轻压下对220 mm×260 mm大方坯轴承钢内部质量的改善[J]. 炼钢, 2018, 34(6): 34-39.
[6]	周彦召，邹长东. 100 t钢包精炼渣系优化选择及应用[J]. 炼钢, 2018, 34(4): 12-16.
[7]	王乐1，刘浏1，姚同路1，王品2. 低成本轴承钢洁净冶炼新工艺的开发[J]. 炼钢, 2018, 34(3): 67-72.
[8]	徐龙云1，2，杨健2，王睿之3，王万林1. Mg含量对焊接热影响区夹杂物及组织的影响[J]. 炼钢, 2017, 33(5): 19-23.
[9]	宋明明1,2，宋波1,3，薛正良2，杨占兵1,3，文彬1,3，胡春林1,3. 稀土处理钢中晶内铁素体的形成及其对性能的影响[J]. 炼钢, 2017, 33(5): 24-30.
[10]	刘浏. 特殊钢发展新趋势与工艺创新[J]. 炼钢, 2017, 33(4): 1-11.
[11]	王乐，刘浏1，王品2. 轴承钢LF精炼深脱硫工艺的研究[J]. 炼钢, 2017, 33(4): 12-18.
[12]	林路1，顾超2，包燕平2，曾加庆1. 20CrMnTi齿轮钢LF精炼渣优化[J]. 炼钢, 2017, 33(2): 15-19.
[13]	邓叙燕1,2，胡楚江1,2，冯传宁1,2. X52抗硫管线钢冶炼工艺优化[J]. 炼钢, 2017, 33(2): 57-62.
[14]	杨进玲，周立新，潘明旭，余亚平，郭畅，张洲，吕文俊. P91耐热钢探伤分层缺陷成因及改进[J]. 炼钢, 2017, 33(2): 69-.
[15]	朱守欣1，于湛1，殷皓1，唐萍2，李敬想2，李玉林2. 轴承钢水口结瘤与棒材中大型夹杂物关系研究[J]. 炼钢, 2017, 33(1): 73-78.